How to calculate conduit fill, with examples for mixed wire sizes (NEC Chapter 9)
Conduit fill is the total cross-sectional area of the conductors divided by the internal area of the conduit. To calculate it by the NEC (2023 edition), add the areas of every conductor, grounds included (Chapter 9, Table 5), divide by the conduit's internal area (Chapter 9, Table 4) and compare with Chapter 9, Table 1: 53% for one conductor, 31% for two, 40% for three or more. Example: ½ in. (1/2 inch) EMT is 0.304 square inches inside, 40% of that is 0.1216 in², and nine 12 AWG THHN conductors at 0.0133 in² each fit. Conduit fill only checks space: more than three current-carrying conductors in one conduit also lowers their ampacity (310.15(C)(1)), and that limit is often reached before the conduit is full.
A fill chart answers "how many of one wire fit in one conduit". Real conduits hold mixed sizes: circuit conductors, a smaller ground, sometimes two circuits. For those you need the calculation, and it is four steps of arithmetic.
What is the maximum conduit fill? The 40% rule
The NEC limits conduit fill to 53% of the conduit's internal area for one conductor, 31% for two and 40% for three or more (Chapter 9, Table 1).
| Conductors in the raceway | Maximum fill | Source |
|---|---|---|
| One | 53% | Chapter 9, Table 1 |
| Two | 31% | Chapter 9, Table 1 |
| Three or more | 40% | Chapter 9, Table 1 |
| Any number, in a nipple of 24 in. or less | 60% | Chapter 9, Note 4 |
Two conductors get the lowest fill limit, 31%, because they lie side by side and can wedge across the diameter of the pipe. The conduit fill limits exist so the wires can be pulled without damaging the insulation and can shed heat once they are in.
How do you calculate conduit fill?
- List every conductor: hots, neutrals and grounds. Equipment grounding conductors count (Note 3 to the Chapter 9 tables).
- Look up each conductor's area with its insulation in Chapter 9, Table 5. The insulation type matters: 12 AWG THHN is 0.0133 in², while 12 AWG THW or XHHW is 0.0181 in². A bare ground uses its area from Table 8.
- Look up the conduit's internal area in Table 4. The conduit type matters: ½ in. EMT is 0.304 in², ½ in. PVC Schedule 40 is 0.285 in² and ½ in. PVC Schedule 80 is 0.217 in².
- Divide the total conductor area by the conduit area and compare with the limit for that number of conductors.
Conductor areas with insulation come from NEC Chapter 9, Table 5, and conduit internal areas from Chapter 9, Table 4:
| Size | Area with insulation |
|---|---|
| 14 AWG | 0.0097 in² |
| 12 AWG | 0.0133 in² |
| 10 AWG | 0.0211 in² |
| 8 AWG | 0.0366 in² |
| 6 AWG | 0.0507 in² |
| 4 AWG | 0.0824 in² |
| Trade size | EMT | EMT at 40% | PVC Sch 40 | PVC Sch 40 at 40% |
|---|---|---|---|---|
| ½ in. | 0.304 in² | 0.1216 in² | 0.285 in² | 0.1140 in² |
| ¾ in. | 0.533 in² | 0.2132 in² | 0.508 in² | 0.2032 in² |
| 1 in. | 0.864 in² | 0.3456 in² | 0.832 in² | 0.3328 in² |
| 1¼ in. | 1.496 in² | 0.5984 in² | 1.453 in² | 0.5812 in² |
Counts for one wire size, 14 AWG to 1/0 in EMT and PVC up to 2 in., are in the conduit fill chart, and how many 12 AWG wires fit in 1/2 and 3/4 in. EMT has that case with the ampacity limit worked out.
Conduit fill calculation examples
Example 1: what size conduit for three 6 AWG and a 10 AWG ground?
A 60 A feeder: two hots, a neutral and a ground, all THHN. Total area: 3 × 0.0507 + 0.0211 = 0.1732 in². Four conductors, so the limit is 40%.
- ½ in. EMT: 0.1732 ÷ 0.304 = 57.0%. Over the limit.
- ¾ in. EMT: 0.1732 ÷ 0.533 = 32.5%. Fits.
So three 6 AWG THHN and a 10 AWG ground need ¾ in. EMT. A mixed run like this is what a one-size chart cannot answer. Feeder sizes for this job are on the subpanel feeder wire size page.
Example 2: two 20 amp circuits in 1/2 in. EMT
Two hots, two neutrals and one shared ground, all 12 AWG THHN: 5 × 0.0133 = 0.0665 in². Fill is 0.0665 ÷ 0.304 = 21.9%, well under 40%. Four of the conductors carry current, so they are derated to 80% (310.15(C)(1)): 30 A × 0.80 = 24 A from the 90 °C column, still enough for 20 A breakers.
Example 3: six 20 amp circuits in 3/4 in. EMT (fill passes, ampacity fails)
Six 20 A circuits with their own neutrals are twelve current-carrying 12 AWG THHN conductors, plus a ground. Fill: 13 × 0.0133 = 0.1729 in², and 0.1729 ÷ 0.533 = 32.4%. It fits.
The ampacity does not pass. Twelve current-carrying conductors fall in the 10 to 20 band of 310.15(C)(1), where the factor is 50%: 30 A × 0.50 = 15 A, too low for a 20 A breaker. The options:
- Split the circuits between two conduits. Up to nine current-carrying 12 AWG THHN conductors keep 70%, which is 21 A.
- Upsize to 10 AWG: 40 A × 0.50 = 20 A. The fill then becomes 12 × 0.0211 + 0.0133 = 0.2665 in², which is 50.0% of ¾ in. EMT. That no longer fits, and the run needs 1 in. EMT (30.8%).
The derating step itself is in how to size wire step by step.
Example 4: two wires in a conduit and the 31% limit
Two 6 AWG THHN in ½ in. EMT, with the EMT itself as the equipment ground (250.118): 2 × 0.0507 = 0.1014 in², which is 33.4%. That is under 40% but over the 31% allowed for two conductors, so it does not fit. Adding a 10 AWG ground wire makes three conductors with a 40% limit, and the fill becomes 40.3%, still just over. The run needs ¾ in. EMT.
Nipples, rounding, bends and cables in conduit
- Rounding. When all conductors are the same size and the calculation ends in 0.8 or more, Note 7 to the Chapter 9 tables allows the next whole number. NEC Annex C is built that way, which is why a chart that always rounds down can show one conductor less.
- Nipples. A conduit of 24 in. or less may be filled to 60% (Note 4), and the derating factors of 310.15(C)(1) do not apply to it.
- Bends. No more than 360° of bends between pull points (358.26 for EMT, 352.26 for PVC). A full conduit with too many bends cannot be pulled even if the fill passes.
- Jamming. Three conductors can lock across the pipe in a bend when the conduit's inside diameter is about three times the conductor's diameter. The note to Table 1 puts the range to avoid at 2.8 to 3.2.
- Cables in conduit. A multiconductor cable is treated as a single conductor using its actual outside dimension, and a flat cable such as NM-B (Romex) as a circle of its larger dimension (Note 9).
- Other conduit types. RMC, IMC, flexible conduit and PVC Schedule 80 each have their own areas in Table 4. Schedule 80 is the tightest: ½ in. holds six 12 AWG THHN where EMT holds nine.
For the box at the end of the run, see box fill calculation.
Conduit fill questions
How do you calculate conduit fill with different wire sizes?
Multiply each wire size's area with insulation (NEC Chapter 9, Table 5) by how many of that size are in the conduit, add the results and divide by the conduit's internal area (Table 4). Three 6 AWG THHN and a 10 AWG THHN ground total 0.1732 in², which is 32.5% of ¾ in. EMT, within the 40% limit.
What is the 40% rule for conduit?
The 40% rule says that with three or more conductors, their total area including insulation may be at most 40% of the conduit's internal area. One conductor may fill 53% and two may fill 31% (NEC Chapter 9, Table 1).
What size conduit do I need for three 6 AWG wires and a ground?
¾ in. EMT. Three 6 AWG THHN conductors (0.0507 in² each) and a 10 AWG THHN ground (0.0211 in²) total 0.1732 in², which is 32.5% of ¾ in. EMT and within the 40% limit of NEC Chapter 9, Table 1. In ½ in. EMT the same conductors would fill 57.0%.
Do ground wires count toward conduit fill?
Yes, ground wires count toward conduit fill. Every conductor in the conduit counts for fill, including equipment grounding conductors (Note 3 to the NEC Chapter 9 tables). They do not count as current-carrying conductors for derating.
How full can a conduit nipple be?
A conduit nipple of 24 in. or less may be filled to 60% of its internal area (NEC Chapter 9, Note 4), and the derating factors of 310.15(C)(1) do not apply to the conductors in it.
Does conduit fill tell me how many circuits I can run in one conduit?
Only partly. Conduit fill checks space, not ampacity. With more than three current-carrying conductors, NEC 310.15(C)(1) reduces their ampacity, and for 12 AWG THHN on 20 A breakers that limit is nine current-carrying conductors, reached well before the conduit is full.
More guides
- 8 AWG or 6 AWG for 50 amps?
- How to calculate box fill
- AWG vs mm²: which sizes are equivalent
- Continuous load: the 125% and 80% rules
- How to size wire step by step
- Voltage drop: 3% or 5%?
Written by Andrii Zhukovskyi, a software developer and the maker of Electrician Calc. He is not a licensed electrician. The numbers follow NFPA 70, National Electrical Code, 2023 edition, and are the values the app uses (methodology and sources); the code text is not reproduced. Under the 2017 NEC, Table 310.16 is Table 310.15(B)(16), 310.15(C)(1) is 310.15(B)(3)(a) and 310.12 is 310.15(B)(7). Found a mistake? Write to [email protected]. Reference only: the edition and amendments adopted where you work, the equipment listing and the manufacturer's instructions govern. NEC® and NFPA 70® are registered trademarks of the National Fire Protection Association; this site is not affiliated with or endorsed by NFPA.