Dre Dev Tools
Tools › Electrical › 12 V DC voltage drop
Electrical reference

12 V DC voltage drop and wire size chart

The smallest copper wire that keeps a 12 V DC run within 3 % or 10 % voltage drop, for 5 to 50 A over 5 to 50 ft.

Quick answer: at 12 V, 3 % is only 0.36 V. A 20 A load 15 ft from the battery needs 6 AWG copper to stay within 3 %, or 12 AWG if a 10 % drop is acceptable.

Checked by Andrii Zhukovskyi. Computed with the same formula as the voltage drop calculator on this site, set to DC.

12 V DC wire size charts

Copper, AWG unless marked kcmil. Length is one way from the source to the load; both conductors are counted.

3 % voltage drop or less (0.36 V)

Current \ one-way length5 ft10 ft15 ft20 ft25 ft30 ft40 ft50 ft
5 A1614121010886
10 A1410886644
15 A128864432
20 A108644321
30 A8643221/02/0
40 A843211/02/03/0
50 A64211/02/03/04/0

10 % voltage drop or less (1.2 V)

Current \ one-way length5 ft10 ft15 ft20 ft25 ft30 ft40 ft50 ft
5 A1818161614141212
10 A181614121212108
15 A16141212101088
20 A161212108866
30 A14121088664
40 A1210866643
50 A128864432

Voltage drop only. Check the wire's ampacity and the fuse rating separately. For 24 V the same wire allows twice the length.

Worked example: 20 A load, 15 ft from the battery, 12 V

  1. On 14 AWG: 2 × 15 ft of wire carry 20 A and drop 1.89 V, which is 15.8 % of 12 V.
  2. To stay within 3 % (0.36 V) the wire has to be 6 AWG: 2.47 %.
  3. If 10 % (1.2 V) is acceptable for the load, 12 AWG is enough: 9.93 %.

Result: 6 AWG for 3 %, 12 AWG for 10 %.

Voltage drop calculator (choose DC)

The whole job, on your phone

Electrician Calc: Wire & Panel

DC, single and three-phase voltage drop, solar PV strings and battery sizing in one app. See what's inside.

Questions

Why does voltage drop matter more at 12 V?

The volts lost depend on current and wire, not on the system voltage. Losing 0.5 V is 0.4 % of 120 V but over 4 % of 12 V, so low-voltage DC runs need much heavier wire for the same percent.

What voltage drop is acceptable on 12 V?

It depends on the load, so this page gives two limits: 3 % (0.36 V) and 10 % (1.2 V). Use the limit the maker of the equipment specifies.

Is the length one way or round trip?

The tables use the one-way distance from the source to the load and already count both the positive and the negative conductor.

What size wire for 20 amps at 12 volts?

For a 15 ft run, 6 AWG keeps the drop within 3 % and 12 AWG within 10 %. Longer runs need larger wire: see the tables.

Does this cover fuse and ampacity?

No. These tables check voltage drop only. The wire must also be rated for the current, and the fuse or breaker must protect the wire. Vehicles and boats have their own wiring standards; follow the one that applies.

How is this calculated?

VD = 2 × K × I × L ÷ CM with K = 12.96 Ω·cmil/ft for copper: resistivity 0.017241 Ω·mm²/m at 20 °C plus 25 % for operating temperature, the resistance the voltage drop calculator on this site uses, set to DC. Cooler wire has slightly less resistance, so real drops are a little lower.

Reference only. The code edition and amendments adopted where you work, the equipment's listing and the manufacturer's instructions govern. Have a licensed electrician check the installation.